Installing on Synology. For Synology, Jellyfin is installed using Docker. Create the container. Use Advanced Settings to add mount points to your media and config. Host Mode is required for HdHR and DLNA.
- Docker Compose For Synology
- Docker For Synology
- Docker Containers For Synology
- Docker For Synology Server
- On a Synology, each share is a BTRFS sub-volume and acts as a different file system. Because of this, copy + move does not execute properly across the different file systems. The old method used multiple BTRFS shares, and therefore multiple file systems.
- Eclipse Mosquitto is an open source message broker which implements MQTT version 5, 3.1.1 and 3.1.
Docker runs in a separate network by default called a docker bridge network, which makes DHCP want to serve addresses to that network and not your LAN network where you probably want it. This document details why Docker Pi-hole DHCP is different from normal Pi-hole and how to fix the problem.
Technical details¶
Docker's bridge network mode is default and recommended as a more secure setting for containers because docker is all about isolation, they isolate processes by default and the bridge network isolates the networking by default too. You gain access to the isolated container's service ports by using port forwards in your container's runtime config; for example -p 67:67 is DHCP. However, DHCP protocol operates through a network 'broadcast' which cannot span multiple networks (docker's bridge, and your LAN network). In order to get DHCP on to your network there are a few approaches:
Working network modes¶
Here are details on setting up DHCP for Docker Pi-hole for various network modes available in docker.
Docker Pi-hole with host networking mode¶
Advantages: Simple, easy, and fast setup
Possibly the simplest way to get DHCP working with Docker Pi-hole is to use host networking which makes the container be on your LAN Network like a regular Raspberry Pi-hole would be, allowing it to broadcast DHCP. It will have the same IP as your Docker host server in this mode so you may still have to deal with port conflicts.
Docker Compose For Synology
- Inside your docker-compose.yml remove all ports and replace them with:
network_mode: host docker run --net=hostif you don't use docker-compose
Docker Pi-hole with a Macvlan network¶
Advantages: Works well with NAS devices or hard port conflicts
A Macvlan network is the most advanced option since it requires more network knowledge and setup. This mode is similar to host network mode but instead of borrowing the IP of your docker host computer it grabs a new IP address off your LAN network.
Having the container get its own IP not only solves the broadcast problem but avoids port conflicts you might have on devices such as NAS devices with web interfaces. Tony Lawrence detailed macvlan setup for Pi-hole first in the second part of his great blog series about Running Pi-hole on Synology Docker, check it out here: Free your Synology ports with Macvlan
Docker Pi-hole with a bridge networking¶
Advantages: Works well with container web reverse proxies like Nginx or Traefik
If you want to use docker's bridged network mode then you need to run a DHCP relay. A relay points to your containers forwarded port 67 and spreads the broadcast signal from an isolated docker bridge onto your LAN network. Relays are very simple software, you just have to configure it to point to your Docker host's IP port 67.
Although uncommon, if your router is an advanced enough router it may support a DHCP relay. Try googling for your router manufacturer + DHCP relay or looking in your router's configuration around the DHCP settings or advanced areas.
Docker For Synology
If your router doesn't support it, you can run a software/container based DHCP relay on your LAN instead. The author of dnsmasq made a very tiny simple one called DHCP-helper. DerFetzer kindly shared his great setup of a DHCP-helper container on the Pi-hole Discourse forums.
Warning about the Default bridge network¶
Docker Containers For Synology
The out of the box default bridge network has some limitations that a user created bridge network won't have. These limitations make it painful to use especially when connecting multiple containers together.
Docker For Synology Server
Avoid using the built-in default docker bridge network, the simplest way to do this is just use a docker-compose setup since it creates its own network automatically. If compose isn't an option the bridge network docs should help you create your own.